TANTEC TECMATE 100

ChemWatch Material Safety Data Sheet 6520-60
Date of issue: Mon 16-Aug-1999

Quick access to sections:
IDENTIFICATION
ACUTE HEALTH EFFECTS
CHRONIC HEALTH EFFECTS
FIRST AID
ADVICE TO DOCTOR
PRECAUTIONS FOR USE
ENGlNEERING CONTROLS
PERSONAL PROTECTION
STORAGE AND TRANSPORT
SPILLS AND DISPOSAL
FIRE/EXPLOSION HAZARD
CONTACT
[home][top]


IDENTIFICATION

STATEMENT OF HAZARDOUS NATURE: HAZARDOUS ACCORDING TO WORKSAFE AUSTRALIA CRITERIA

SUPPLIER
Company: Tantec Ltd
Address: P O Box 65 404; Mairangi Bay; Auckland 1330; New Zealand
Telephone: +64 9 415 8774
Emergency Tel: 0800 429243
Fax:: +64 9 415 8775
 
Product Name:
CAS RN No(s):
UN Number:
Packaging Group:
Dangerous Goods Class:
Subsidiary Risk:
Hazchem Code:
Poisons Schedule Number:
Tantec Tecmate 100
None
None
None
None
None
None
NZ S4

USE: Preservative.

PHYSICAL DESCRIPTION/PROPERTI ES
APPEARANCE: Clear alkaline liquid with a weak odour; mixes with water.
 
Boiling Point (deg C):
Melting Point (deg C):
Vapour Pressure (kPa):
Specific Gravity:
Flash Point (deg C):
Lower Explosive Limit (%):
Upper Explosive Limit (%):
Solubility in Water (g/L):
Not available
Not available
Not available
Not available
Not applicable
Not applicable
Not applicable
Miscible

INGREDIENTS
NAME
sodium dimethyldithiocarbamate
sodium hydroxide
water
CAS RN
128-04-1
1310-73-2
7732-18-5 
%
30-60
0.5max .
30-60



ACUTE HEALTH EFFECTS
SWALLOWED: Considered an unlikely route of entry in commerclallindustrial environments. The liquid is discomforting to the gastrointestinal tract and harmful if swallowed. Ingestion may result in nausea, albdominal irritation, pain and vomiting. The acute toxicity of thiocarbamates is generally low. When administered in high doses, signs such as anorexia. squinting, hypersalivation, lachrymation, piloerection, laboured breathing, ataxia, hypothermia, incoordination, depression, pareses and muscular fibrillation may occur.
While thiocarbamates and their metabolites can be found in certain organs such as liver and kidney, accumulation does not take place because of their rapid metabolism.

EYE: The material may be irritating to the eye, with prolonged contact causing inflammation. Repeated or prolonged exposure to irritants may produce conjunctivitis.

SKIN: The material may cause skin irritation after prolonged or repeated exposure and may produce a contact dermatitis (nonallergic). This form of dermatitis is often characterised by skin redness (erythema) and sweling (oedema) which may progress to vesiculation, scaling and thickening of the epidermis. Histologically there may be intercellular oedema of the spongy
layer (spongiosis) and intracellular oedema of the epidermis.

INHALED: Not normally a hazard due to non-volatile nature or product. The mist is discomforting to the upper respiratory tract.



CHRONIC HEALTH EFFECTS: Principal routes of exposure are usualiy by skin contact/ eye contact. As with any chemical product. contact with unprotected bare skin; inhalation of vapour, mist or dust in work place atmosphere; or ingestion in any form, should be avoided by observing good occupational work practice.


FIRST AID
SWALLOWED: DO NOT induce vomiting. Observe the patient carefully. Never give liquid to a person showing signs
of being sleepy or with reduced awareness i.e. becoming unconscious. Give water (or milk) to rinse out mouth. Then provide liquid slowly and as much as casualty can comfortably drink. Seek medical advice.

EYE: If this product comes in contact with the eyes: Immediately hold the eyes open and wash with fresh running water. Ensure irrigation under the eyelids by occasionally lifting upper and lower lids. If pain persists or recurs seek medical attention. Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.

SKIN: If product comes in contact with the skin: Immediately remove all contaminated clothing, including footwear (after rinsing with water). Wash affected areas thoroughly with water (and soap if available). Seek medical attention in event of irritation

INHALED: If fumes or combustion products are inhaled: Remove to fresh air. Lay patient down.  Keep warm and rested. If breathing is shallow or has stopped, ensure clear airway and apply resuscitation. Transport to hospital or doctor.



ADVICE TO DOCTOR: Medical literature on human exposure to thiocarbamate derivatives is scarce.

PRECAUTIONS FOR USE: None assigned. Refer to individual constituents:
Sodium hydroxide
TLVC: 2 mg/m3
ES Peak: 2 mg/m3
OES STEL: 2 mg/m3
IDLH level: 250 mg/m3
The TLV-C is recommended based on concentrations that produce noticeable but not excessive, ocular and upper respiratory tract irritation.


ENGlNEERING CONTROLS: General exhaust is adequate under normal operating conditions. Local exhaust ventilation may be required in specific circumstances. If risk of overexposure exists, wear SAA approved respirator. Correct fit is essential to obtain adequate protection. Provide adequate ventilation in warehouse or closed storage areas.


PERSONAL PROTECTION

EYE: Safety glasses with side shields; or as required, Chemical goggles. Contact lenses pose a special hazard; soft lenses may absorb irritants and all lenses concentrate them.

HANDS/FEET: Wear chemical protective gloves. eg. PVC gloves with barrier cream. Wear safety footwear.

OTHER: Overalls. Eyewash unit.

RESPIRATOR: Selection of the Class and Type of respirator will depend upon the level of breathing zone contaminant and the chemical nature of the contaminant. Protection Factors (defined as the ratio of contaminant outside and inside the mask) may also be important.
 
Breathing Zone 
Level ppm (volume)
----------------------
  1000
  1000
  5000
  5000
10000
Maximum
Protection Factor
----------------------
  10
  50
  50
100
100 
100+ 
Half-face
Respirator
----------------------
-AUS P
-
Airline*
-
-
-
Full-Face
Respirator
----------------------
-
-AUS P
-
-2P
-3P
Airline**
*- Continuous Flow.   ** - Continuous-flow or positive pressure demand.

The local concentration of material, quantity and conditions of use determine the type of personal protective equipment required. For further information, consult site specific CHEMWATCH data (if available), or your Occupational Health and Safety Advisor.



STORAGE AND TRANSPORT

SUITABLE CONTAINER: Polyethylene or polypropylene container. Plastic carboy Plastic drum. Polyliner drum.
Packing as recommended by manufacturer. Check all containers are clearly labelled and free from leaks.

STORAGE INCOMPATIBILITY: Avoid storage with oxidisers and acids.

STORAGE REQUIREMENT: Store in original containers. Keep containers securely sealed. Store in a cool, dry, well-ventilated area. Store away from incompatible materials and foodstuff containers. Protect containers against physical damage and check regularly for leaks. Observe manufacturer's storing and handling recommendations

TRANSPORTATION: No restrictions.



SPILLS AND DISPOSAL
MINOR SPILLS: Clean up all spills immediately. Avoid breathing vapours and contact with skin and eyes. Control personal contact by using protective equipment. Contain and absorb spill with sand, earth, inert material or vermiculite. Wipe up. Place in a suitable labelled container for waste disposal.

MAJOR SPILLS: Minor hazard. Clear area of personnel. Alert Fire Brigade and tell them location and nature of hazard. Control personal contact by using protective equipment as required. Prevent spillage from entering drains or water ways. Contain spill with sand, earth or vermiculite. Collect recoverable product into labelled containers for recycling. Absorb remaining product with sand, earth or vermiculite and place in appropriate containers for disposal. Wash area and prevent runoff into drains or waterways. If contamination of drains or waterways occurs, advise emergency services.

DISPOSAL: Recycle wherever possible or consult manufacturer for recycling options. Consult State Land Waste Management Authority for disposal. Bury residue in an authorised landfill. Recycle containers where possible, or dispose of in an authorised landfill.



FIRE/EXPLOSION HAZARD:  Non combustible. Not considered to be a significant fire risk. Expansion or decomposition on heating may lead to violent rupture of containers. Decomposes on heating and may produce toxic fumes of carbon monoxide (CO). May emit acrid smoke. Other decomposition products include carbon dioxide (C02), sulfur oxides (SOx), nitrogen oxides (NOx) and hydrogen sulfide (H2S).


CONTACT
AUSTRALIAN POISONS INFORMATION CENTRE
24 HOUR SERVICE             :- 13 11 26
POLICE OR FIRE BRIGADE    :- 000    (exchange):-1 100

NEW ZEALAND POISONS INFORMATION CENTRE
Dunedin  -(03)479 1200  (Normal Hours), (03)474 0999 (Emergency)



[home][top]